AEG Washing machine
| E11 | · Poor fill before wash cycle · Tap off or water pressure too low · Drain hose improperly positioned · Fill valve is defective · Leaks on pressure switch · Pressure switch failed · Wiring fault · Main board defective · Cycle is paused with door locked Start |
This is usually is related to water supply error. Basic checks are required – checking water stop cock , water pressure , blockage from lime scale on inlet pipe.
| E12 | · Difficulty in fill during drying · Tap off or water pressure too low valve failed · Pressure switch water circuit · Pressure switches · Wiring · Main PCB |
| E13 | · Water leaks drain hose improperly positioned · Water pressure too low · Fill valve is defective · Water circuit on pressure switch is leaking or blocked · Pressure switch faulty · Cycle is paused with door locked |
| E21 | · Poor draining · Drain hose kinked/clogged/improperly positioned · Drain filter clogged/dirty · Drain pump faulty · Pressure switch faulty · Wiring faulty · Main board faulty · Current leak between heating element and ground |
| E22 | · Difficulty in fill during drying or drying condenser blocked (pressure switch closed on “FULL”) · Drain hose kinked · Filter blocked · Drying condenser blocked · Drain pump faulty · Pressure switches faulty · Wiring · Main circuit board faulty · Current leakage between heater and ground |
| E23 | · Defective triac for drain pump · Drain pump faulty · Wiring faulty · Main board faulty |
| E24 | · Malfunction in sensing circuit on triac for drain pump · Main board faulty |
| E31 | · Malfunction in pressure switch circuit · Pressure switch faulty · Wiring · Main PCB faulty |
| E32 | · Electronic pressure switch improperly calibrated · Tap is off or water pressure is too low · Fill valve faulty · Water circuit on pressure switches · Pressure switches · Wiring · PCB faulty · Cycle is paused Start |
| E33 | · Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 1-2 (fault persists for at least 60 sec.) · Pressure switch defective · Current leak between heating element and ground · Heating element · Wiring faulty · Main board faulty · Water circuit |
| E34 | · Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2 (fault persists for at least 60 sec.) · Pressure switch faulty · Electrical current leak between heating element and ground · Heating element faulty · Wiring faulty · Main board faulty · Water circuit |
| E35 | · Overflow error · Fill valve is faulty · Leaks from water circuit on pressure switch · Pressure switch defective · Wiring defective · Main board defective |
| E36 | · Sensing circuit on anti-boiling pressure switch 1 defective · Main board faulty · Cycle stops with door locked OFF/reset |
| E37 | · Sensing circuit on anti-boiling pressure switch 2 defective · Main board faulty · Cycle stops with door locked OFF/reset |
| E38 | · Internal pressure takeoff is blocked (water level does not change for at least 30 sec of drum rotation) · Water circuit on pressure switches · Pressure switches · Motor belt broken · Heating phase is skipped |
| E39 | · Defective HV sensing on anti-overflow system · Main board faulty |
| E3A | · Faulty sensing by heating resistance relay · Main board defective. |
| E41 | · Door unlocked · Door lock faulty · Wiring faulty · Main board faulty |
| E42 | · Problem closing the door · Door lock faulty · Wiring faulty · Main board faulty |
| E43 | · Defective triac supplying power to door delay system · Door lock unit faulty · Wiring faulty · Main board faulty |
| E44 | · Defective sensing by door delay system · Main board faulty |
| E45 | · Defective sensing by triac on door delay system · Main board faulty |
| E51 | · Motor power supply triac short-circuited · PCB faulty · Current leakage from motor or from wiring loom |
| E52 | · No signal from motor tachometric generator · Motor faulty · Wiring faulty · PCB faulty |
Tacho coil on the motor is most probably faulty. This coil reads a magnet as the motor turns to detect the speed that the motor is spinning at and this in turn allows the electronic controller to set the motor to revolve at different speeds for the various program options.
| E53 | · Motor triac sensing circuit faulty · PCB faulty |
| E54 | · Motor relay contacts sticking · PCB faulty · Current leakage from motor or from wiring |
| E61 | · Insufficient heating during washing · NTC sensor faulty · Heating element faulty · Wiring faulty · PCB faulty · The heating phase is skipped |
| E62 | · Overheating during washing · NTC sensor faulty · Heating element faulty · Wiring faulty · PCB faulty |
| E66 | · Heating element power relay faulty · PCB faulty · Current leakage from heating element to ground |
| E71 | · NTC sensor for wash cycle defective · Faulty NTC sensor · Wiring faulty · Main board faulty · Heating is skipped revert to Start |
| E72 | · Fault in NTC sensor on drying condenser · Drying NTC sensor (condenser) faulty · Wiring faulty · Main circuit board faulty · Heating is skipped revert to Start |
| E73 | · Fault in NTC sensor on drying duct · Drying NTC sensor faulty · Wiring faulty · Main circuit board faulty |
| E74 | · NTC sensor for wash cycle improperly positioned · NTC sensor incorrectly positioned · Faulty NTC sensor · Wiring defective · Main board faulty |
| E82 | · Error in selector reset position · PCB faulty (Wrong configuration data) · Selector, wiring faulty |
| E83 | · Error in reading selector · PCB faulty (Wrong configuration data) · Selector, wiring · Cycle cancelled |
| E84 | · Sensing circuit on circulation pump triac faulty · PCB Drain · Cycle blocked (door open) |
| E85 | · Circulation pump faulty · Wiring · Main PCB · Drain, cycle blocked (door open) |
| E91 | · Communication incongruence between main PCB- display board (versions not compatible) · Wiring faulty · Faulty control/display board · Main PCB faulty |
| E92 | · Communication incongruence between main PCB- display board (versions not compatible) · Wrong control/display board · Wrong PCB (do not correspond to the model) |
| E93 | · Incorrect configuration of appliance · Incorrect configuration data · PCB faulty |
| E94 | · Incorrect configuration of washing cycle · Incorrect configuration data · PCB faulty |
| E95 | · Communication error between microprocessor and EEPROM · PCB faulty |
| E97 | · Incongruence between programme selector and cycle configuration · Faulty PCB (Wrong configuration data) |
| EB1 | · Frequency of appliance incorrect · Power supply problems (incorrect / disturbance) · PCB faulty |
| EB2 | · Voltage too high Power supply problems (incorrect / disturbance) · PCB faulty |
| EB3 | · Voltage too low · Power supply problems (incorrect / disturbance) · PCB faulty |
| EC1 | · Solenoid valve inoperative but flow meter operating · Main board faulty · Fill valve faulty |
| EC2 | · Signal from turbidity sensor out of limits · Turbidity sensor faulty · Main board faulty · Wiring faulty |
| EC3 | · Signal from weight sensor out of limits · Weight sensor faulty · Main board faulty · Wiring faulty |
| EF1 | · Drain filter blocked (too long drain phase) · Drain tube blocked/kinked/too high · Drain filter dirty/blocked · Warning displayed at the end of cycle (specific LED) |
| EF2 | · Overdosing of detergent (too much foam during drain phases) · Excessive detergent dosing · Drain tube kinked/blocked · Drain filter dirty/blocked |
| EF3 | · Control water intervention · Water leakage on the base · Faulty water control device · Water drain and cycle blocked |
| EF4 | · Low pressure of water fill, no signal of flow meter and solenoid open · Tap closed, low water fill pressure |
| E00 | · No alarm |
