AEG Washing machine

Home › Forums › AEG Error Codes › AEG Washing machine

Viewing 1 post (of 1 total)
  • Author
    Posts
  • 4th January 2019 at 2:18 pm #7238
    happyappliances
    Keymaster
    E11·       Poor fill before wash cycle

    ·       Tap off or water pressure too low

    ·       Drain hose improperly positioned

    ·       Fill valve is defective

    ·       Leaks on pressure switch

    ·       Pressure switch failed

    ·       Wiring fault

    ·       Main board defective

    ·       Cycle is paused with door locked Start

    This is usually is related to water supply error. Basic checks are required – checking water stop cock , water pressure , blockage from lime scale on inlet pipe.

    E12·       Difficulty in fill during drying

    ·       Tap off or water pressure too low valve failed

    ·       Pressure switch water circuit

    ·       Pressure switches

    ·       Wiring

    ·       Main PCB

     

    E13·       Water leaks drain hose improperly positioned

    ·       Water pressure too low

    ·       Fill valve is defective

    ·       Water circuit on pressure switch is leaking or blocked

    ·       Pressure switch faulty

    ·       Cycle is paused with door locked

     

    E21·       Poor draining

    ·       Drain hose kinked/clogged/improperly positioned

    ·       Drain filter clogged/dirty

    ·       Drain pump faulty

    ·       Pressure switch faulty

    ·       Wiring faulty

    ·       Main board faulty

    ·       Current leak between heating element and ground

     

    E22·       Difficulty in fill during drying or drying condenser blocked (pressure switch closed on “FULL”)

    ·       Drain hose kinked

    ·       Filter blocked

    ·       Drying condenser blocked

    ·       Drain pump faulty

    ·       Pressure switches faulty

    ·       Wiring

    ·       Main circuit board faulty

    ·       Current leakage between heater and ground

     

    E23·       Defective triac for drain pump

    ·       Drain pump faulty

    ·       Wiring faulty

    ·       Main board faulty

     

    E24·       Malfunction in sensing circuit on triac for drain pump

    ·       Main board faulty

     

    E31·       Malfunction in pressure switch circuit

    ·       Pressure switch faulty

    ·       Wiring

    ·       Main PCB faulty

     

    E32·       Electronic pressure switch improperly calibrated

    ·       Tap is off or water pressure is too low

    ·       Fill valve faulty

    ·       Water circuit on pressure switches

    ·       Pressure switches

    ·       Wiring

    ·       PCB faulty

    ·       Cycle is paused Start

     

    E33·       Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 1-2 (fault persists for at least 60 sec.)

    ·       Pressure switch defective

    ·       Current leak between heating element and ground

    ·       Heating element

    ·       Wiring faulty

    ·       Main board faulty

    ·       Water circuit

     

    E34·       Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2 (fault persists for at least 60 sec.)

    ·       Pressure switch faulty

    ·       Electrical current leak between heating element and ground

    ·       Heating element faulty

    ·       Wiring faulty

    ·       Main board faulty

    ·       Water circuit

     

    E35·       Overflow error

    ·       Fill valve is faulty

    ·       Leaks from water circuit on pressure switch

    ·       Pressure switch defective

    ·       Wiring defective

    ·       Main board defective

     

    E36·       Sensing circuit on anti-boiling pressure switch 1 defective

    ·       Main board faulty

    ·       Cycle stops with door locked OFF/reset

     

    E37·       Sensing circuit on anti-boiling pressure switch 2 defective

    ·       Main board faulty

    ·       Cycle stops with door locked OFF/reset

     

    E38·       Internal pressure takeoff is blocked (water level does not change for at least 30 sec of drum rotation)

    ·       Water circuit on pressure switches

    ·       Pressure switches

    ·       Motor belt broken

    ·       Heating phase is skipped

     

    E39·       Defective HV sensing on anti-overflow system

    ·       Main board faulty

     

    E3A·       Faulty sensing by heating resistance relay

    ·       Main board defective.

     

    E41·       Door unlocked

    ·       Door lock faulty

    ·       Wiring faulty

    ·       Main board faulty

     

    E42·       Problem closing the door

    ·       Door lock faulty

    ·       Wiring faulty

    ·       Main board faulty

     

    E43·       Defective triac supplying power to door delay system

    ·       Door lock unit faulty

    ·       Wiring faulty

    ·       Main board faulty

     

    E44·       Defective sensing by door delay system

    ·       Main board faulty

     

    E45·       Defective sensing by triac on door delay system

    ·       Main board faulty

     

    E51·       Motor power supply triac short-circuited

    ·       PCB faulty

    ·       Current leakage from motor or from wiring loom

     

    E52·       No signal from motor tachometric generator

    ·       Motor faulty

    ·       Wiring faulty

    ·       PCB faulty

    Tacho coil on the motor is most probably faulty. This coil reads a magnet as the motor turns to detect the speed that the motor is spinning at and this in turn allows the electronic controller to set the motor to revolve at different speeds for the various program options.

    E53·       Motor triac sensing circuit faulty

    ·       PCB faulty

     

    E54·       Motor relay contacts sticking

    ·       PCB faulty

    ·       Current leakage from motor or from wiring

     

    E61·       Insufficient heating during washing

    ·       NTC sensor faulty

    ·       Heating element faulty

    ·       Wiring faulty

    ·       PCB faulty

    ·       The heating phase is skipped

     

    E62·       Overheating during washing

    ·       NTC sensor faulty

    ·       Heating element faulty

    ·       Wiring faulty

    ·       PCB faulty

     

    E66·       Heating element power relay faulty

    ·       PCB faulty

    ·       Current leakage from heating element to ground

     

    E71·       NTC sensor for wash cycle defective

    ·       Faulty NTC sensor

    ·       Wiring faulty

    ·       Main board faulty

    ·       Heating is skipped revert to Start

     

    E72·       Fault in NTC sensor on drying condenser

    ·       Drying NTC sensor (condenser) faulty

    ·       Wiring faulty

    ·       Main circuit board faulty

    ·       Heating is skipped revert to Start

     

    E73·       Fault in NTC sensor on drying duct

    ·       Drying NTC sensor faulty

    ·       Wiring faulty

    ·       Main circuit board faulty

     

    E74·       NTC sensor for wash cycle improperly positioned

    ·       NTC sensor incorrectly positioned

    ·       Faulty NTC sensor

    ·       Wiring defective

    ·       Main board faulty

     

    E82·       Error in selector reset position

    ·       PCB faulty (Wrong configuration data)

    ·       Selector, wiring faulty

     

    E83·       Error in reading selector

    ·       PCB faulty (Wrong configuration data)

    ·       Selector, wiring

    ·       Cycle cancelled

     

    E84·       Sensing circuit on circulation pump triac faulty

    ·       PCB Drain

    ·       Cycle blocked (door open)

     

    E85·       Circulation pump faulty

    ·       Wiring

    ·       Main PCB

    ·       Drain, cycle blocked (door open)

     

    E91·       Communication incongruence between main PCB- display board (versions not compatible)

    ·       Wiring faulty

    ·       Faulty control/display board

    ·       Main PCB faulty

     

    E92·       Communication incongruence between main PCB- display board (versions not compatible)

    ·       Wrong control/display board

    ·       Wrong PCB (do not correspond to the model)

     

    E93·       Incorrect configuration of appliance

    ·       Incorrect configuration data

    ·       PCB faulty

     

    E94·       Incorrect configuration of washing cycle

    ·       Incorrect configuration data

    ·       PCB faulty

     

    E95·       Communication error between microprocessor and EEPROM

    ·       PCB faulty

     

    E97·       Incongruence between programme selector and cycle configuration

    ·       Faulty PCB (Wrong configuration data)

     

    EB1·       Frequency of appliance incorrect

    ·       Power supply problems (incorrect / disturbance)

    ·       PCB faulty

     

    EB2·       Voltage too high Power supply problems (incorrect / disturbance)

    ·       PCB faulty

     

    EB3·       Voltage too low

    ·       Power supply problems (incorrect / disturbance)

    ·       PCB faulty

     

    EC1·       Solenoid valve inoperative but flow meter operating

    ·       Main board faulty

    ·       Fill valve faulty

     

    EC2·       Signal from turbidity sensor out of limits

    ·       Turbidity sensor faulty

    ·       Main board faulty

    ·       Wiring faulty

     

    EC3·       Signal from weight sensor out of limits

    ·       Weight sensor faulty

    ·       Main board faulty

    ·       Wiring faulty

     

    EF1·       Drain filter blocked (too long drain phase)

    ·       Drain tube blocked/kinked/too high

    ·       Drain filter dirty/blocked

    ·       Warning displayed at the end of cycle (specific LED)

     

    EF2·       Overdosing of detergent (too much foam during drain phases)

    ·       Excessive detergent dosing

    ·       Drain tube kinked/blocked

    ·       Drain filter dirty/blocked

     

    EF3·       Control water intervention

    ·       Water leakage on the base

    ·       Faulty water control device

    ·       Water drain and cycle blocked

     

    EF4·       Low pressure of water fill, no signal of flow meter and solenoid open

    ·       Tap closed, low water fill pressure

     

    E00·       No alarm
  • Author
    Posts
Viewing 1 post (of 1 total)
  • You must be logged in to reply to this topic.